MICS 0x32 Meridian Norstar modular ICS Nortel phone system cabinet 0x16 12x0 module LS/DS cartridge card buy quote

4x0 LS/DS Trunk Cartridge

This Loop Start/Disconnect Supervision trunk cartridge supports disconnect supervision, and provides access for up to 4 analog central office lines. This trunk cartridge is compatible with the Compact ICS, the Modular 8X24. It may be inserted into the Compact ICS core trunk slots, the Modular ICS core trunk slots, the Copper Trunk Module or the Fiber Trunk Module.

4x0 Caller ID Trunk Cartridge

The CI trunk cartridge is a loop start, analog trunk cartridge with the capability to detect and translate incoming CMS/CLASS information from the central office for display and use on Norstar station sets. It supports disconnect supervision, and provides access for up to 4 central office lines. This trunk cartridge is compatible with the Compact ICS, and Modular 8x24 (Release DR5 or higher). It may be inserted into the Compact ICS core trunk slots, the Modular ICS core trunk slots, the Copper Trunk Module or the Fiber Trunk Module.

DID Trunk Cartridge

The Direct Inward Dialing Trunk cartridge routes calls from the public network directly to Norstar station sets, bypassing an attendant and therefore reducing traffic to the central answering position. This card provides access for up to 4 central office lines. This trunk cartridge is compatible with the Modular 8x24 (Release DR4 or higher) and the Modular ICS and supports disconnect supervision, but does not support CMS/CLASS services. It may be inserted into either the Copper Trunk Module or the Fiber Trunk Module.

12x0 Fiber Trunk Module

The Fiber Trunk Module is installed in conjunction with a 2 Port or 6 Port Expansion Cartridge and allows the addition of up to three Trunk Cartridges. The Fiber Trunk Module requires a power bar for installation. The Fiber Trunk Module user fiber-optic DS-30 cables instead of copper DS-30 cables. For use on the Modular ICS only.

0x16 Fiber Station Module

The Fiber Station Module is installed in conjunction with a 2 Port or 6 Port Fiber Expansion Cartridge and allows the addition of up to 16 station sets. The Fiber Station Module requires a power bar for installation. The Fiber Station Module uses fiber-optic DS-30 cables instead of copper DS-30 cables. For use on the Modular ICS only.

2 Port Fiber Expansion Card

This cartridge allows the addition of up to two Fiber Trunk or Fiber Station Modules. The cartridge is required to enlarge the system beyond the base controller. The cartridge uses a fiber-optic DS-30 cable that is included. For use on the Modular ICS only.

6 Port Fiber Expansion Card

This cartridge allows the addition of up to six Fiber Trunk or Fiber Station Modules. This cartridge is required to enlarge the system beyond the base controller. This cartridge uses a fiber-optic DS-30 cable that is included. For use on the Modular ICS only.

0x8 Analog Station Module

The Norstar Analog Station Module serves as an interface between a Norstar-PLUS Modular ICS and analog devices such as FAX machines, FAX Modems, credit card verification devices, as well as analog voice equipment. The ASM is an 8 port module that connects to the Modular ICS unit via a Modular ICS Fiber Expansion Cartridge. Two ASMs may be daisy-chained together and connected to a single fiber receptacle on an expansion cartridge. The ASM supports the same features and functionality as the ATA-2. The ASM will support data modem transmission speeds up to 33.6 kb/s.

6 Port Fiber Combo/Expansion

This Combo Cartridge allows the addition of up to six Fiber Trunk or Fiber Station Modules. As well as the Services cartridge functions for DTI synchronization to the T1 network clock or act as a master clock source, providing the clock signal for networked systems. The Combo Cartridge also supports DTMF tone recognition for T1 circuits. One Combo Cartridge will support two DTI cartridges, but for systems with growth potential past six ports, two Combo Cartridges could be used to double the DTMF capabilities for T1 circuits. This cartridge uses a fiber-optic DS-30 cable that is included when enlarging the system past six ports with T1 networking.

Digital Trunk T1 Cartridge

The Digital Trunk Interface (DTI) terminals a 24-channel T1 link from a public or private network. It will also support fractional T1. An RJ48 jack provides the interface to the T1 network. Each of the 24 channels can be configured to emulate either loop-start, E&M, or DID trunks. The DTI has an integrated Channel Services Unit (CSU). The CSU provides line isolation, signal regeneration, and network performance monitoring. The CSU can be turned off for use with an external CSU. Must use with clock services cartridge. For use on the Modular ICS only.

ATA 2 - Analog Terminal Adapter

The ATA2 analog terminal adapter converts a digital extension into analog in order to create single line capability. The ATA 2 is great for adding long range cordless phones, fax machines, and other single line devices to your Norstar system.

FastRAD - Fast Remote Access Device

The FastRAD - Fast Remote Access Device - is an integral part of local and remote administration and maintenance capabilities of Norstar. The FastRAD is the physical interface hardware that is located on the customer premises. PC applications such as Norstar Remote Utilities use a modem to call and connect to the FastRAD at the Norstar system. The FastRAD integral modem will support baud rates from 4800 to 14,400 for external connections and 300 to 19,200 for local or direct connections. The FastRAD is connected to the system using a TCM port, and answers a call on the Norstar system CO line using its internal modem. The FastRAD is powered by a separate power supply. The FastRAD is compatible with all Norstar systems with DR2 software or higher.